Sorry
I do not know who to ask about my problem
mdpna-465 with lower overhead bar reinstalled with the wrong ROM
Now it's dead does not come on screen, no PC connection
There are power buttons work
With 9 pin of flash is not starting
I have the original ROM
Please if you can help with ideas, photos, instructions
I can not get him to the world, Booth
pp sorry for bad english
:017::017:
mdpna-465
-
- [GoPal bis 3.x]
- helpos
-
-
-
-
Ok how does the PNA look like?
Like Picture one
[Blockierte Grafik: http://www.gopal-navigator.de/wiki/images/thumb/9/94/465T-komplett.jpg/788px-465T-komplett.jpg]or Picture two?
[Blockierte Grafik: http://www.gopal-navigator.de/wiki/images/thumb/7/7b/470T-komplett.jpg/788px-470T-komplett.jpg]i mean the bottom side ... Have you this contact "bar" ?
-
Ok how does the PNA look like?
Like Picture one
[Blockierte Grafik: http://www.gopal-navigator.de/wiki/images/thumb/9/94/465T-komplett.jpg/788px-465T-komplett.jpg]or Picture two?
[Blockierte Grafik: http://www.gopal-navigator.de/wiki/images/thumb/7/7b/470T-komplett.jpg/788px-470T-komplett.jpg]i mean the bottom side ... Have you this contact "bar" ?
yes i havePhoto 2 is bottom connector
reinstall it with a ROM of 510 and has finished reinstalling, died
now I have prepared ROM 465t but I can not get him to leave
this is my problem -
?
Does the bottom of your device look like picture one or two?
-
Photo 2 is bottom connector
device is "BLUEMEDIA-BM6600" FULL analogue mdpna465t
the board wrote PWA-MDPNA470T_MAIN_BD
PCB: 316162300005_R02
to replace flash memory, or some secret way to go? -
when connecting usb cable LED lights and really charge the battery
Pressing the power after 2-3 seconds coming PSUs 3.3 volts and 1.7 volts for the CPU but display no lights and no connection to Pc -
As a user of our board wrote its a 465 with multiconnector.
SO this would be the right download for you:
http://www.gopal-navigator.de/downloads.php?do=file&id=302Do you know how to flash?
I hope you can enter the "blue flash screen" after wrong flashing on your side -
when connecting usb cable LED lights and really charge the battery
Pressing the power after 2-3 seconds coming PSUs 3.3 volts and 1.7 volts for the CPU but display no lights and no connection to PC
Whats happenning when you press both buttons on the right side.. (if there are two buttons present)
Does your device look like:
[Blockierte Grafik: http://bilder4.preissuchmaschine.de/prodfoto/bluemediabm6600.jpg]
?By the way: do you have a GoPal Software for the installation after flashing?
-
any button to push "power, poi, reset" or three buttons, only includes the supply and ..... nothing happens, screen does not light
I need a blue screen "bootloader" then I know what to do
just hurry and messed ROM files
then I can put whatever I want navigation software
help boot rom
YES i have this ROM http://www.gopal-navigator.de/downloads.php?do=file&id=302 -
There is only one way to enter the boot-menue.
Hold the Power and only the power button on hold until the blue LED blinks up for one time - than it is really OFF.Then press and hold the "Flag" Button pressed. (nothing will happen)
additional (hold the Flag-Button still pressed) press the power button, so you are finally pushing both buttons... The blue menue should appear now.I go to bed now... I hope you get it run..
-
Yes many are right ...... but this is valid if the device is the correct rom if the device is functioning normally, but it never leaves
I also loaded it with 510 ROM and then load and drew it ready and then not starting
Nothing happens
Other ideas?
A little history
1. device works well with "go-pall" software
2. I want to put his "igo, garmin, sygic ........"
3. I want to change the ROM because it is old and is unlocked
4. change it (but incorrect)
5. device dies
6. what to do ........................
well if you want, and you can help me
please
helpos@abv.bg -
Has anyone any ideas?
-
If you did flash your BM with the wrong ROM (510) (i.e. you obviously know the way to flash it) and your PNA doesn't show any reaction while trying to flash once more again I suppose it has been destroyed now. I don't have any ideas left which would help you.
EDIT: ok, probably it might help if you disconnect the accu for about 15 min, but I'm not that hopeful
-
Not helping the exclusion of battery "1-2 days"
when you press the "power" processor manages power 3.3 volt and 1.7 volt
again when pressing the "power" processor power stop
I do not know whether replacing the flash will help? -
Monika
Hat das Thema aus dem Forum GoPal Software nach MEDION mobile Navis (PNA) verschoben. -
Monika
Hat das Label [GoPal bis 3.x] hinzugefügt.